產品詳情
進口數顯可調渦輪流量表 甲醇 柴油 煤油 化學液體水流量計量表 昆山天天測溫儀表有限公司
LCD屏數顯渦輪流量計使用說明書一、產品介紹
JK-K24流量計控制面板采用模塊化設計，具有功能完備，結構簡單，操作方便等特點?？梢詮V泛用于石油、化工、醫藥、交通、食品待工業及商業。
二、技術參數
介質 柴油，尿素，煤油，化學品，汽油，水
進出口 1"
計量精度 ±1%
重復性 ±0.5%
最大工作壓力 20BAR
工作電壓 2.3-3.3V
待機時間 2年
流量范圍 10-120L/MIN
單次計數 0.00-9999.9
總累計數 0.00-999999.9
計量單位 升/L，加侖/GAL，品脫/PTS，夸脫/QTS
單次計量清零 RESET
三、計量設置
1、計量單位設置
在待機狀態或當前加注量顯示狀態下，同時按MENU+RESET鍵5秒鐘。進入單位轉換設置，按RESET按鍵，依次按LTR→GAL→PT→QT→LTR選擇計量單位，同時累計加注量按照當前的計量單位換算后顯示。再按MENU鍵3秒鐘，退出單位轉換設置。
2、可復位累計加注量清零。
長按RESET鍵，LCD滿屏顯視，等待滿屏顯視結束后，松開RESET鍵，此時可復位累計加注量與當前加注量清零。
3、誤差系數與總累計查詢
待機狀態下，同時按MENU+RESET鍵，LCD上排數字顯視誤差系數，下排顯視總累計流量。
四、誤差系數標定
在待機狀態或當前加注量顯示狀態下，按MENU按鍵3秒鐘，進入誤差系數標定狀態。同時第一位數字閃爍顯示，按MENU按鍵，數字移位，（閃爍數字位移），按RESET按鍵，修改當前閃爍位的數值，依次從0到9，再到0。此系數增大時出油量越少，系數越小出油量越多。按MENU按鍵3秒鐘結束誤差系數標定。返回到顯示當前加注量狀態，并且當前加注量顯示清零。誤差系數標定后，如有新的計量脈沖輸入則使用新設的誤差系數進行標定。誤差系數標定范圍：0.1000—9.9999。例原系數為1.000時，顯示屏顯示油100升，實際出油也是100升，如想少加2升油，按MENU按鍵3秒鐘，按誤差系數標定里的調到1.020。以后就是98升。想要96升就調到1.040。反之則少顯多給油。
五、維護與保養
當電池電壓過低時，LCD顯視屏上出現電池標志，提醒用戶需要更換電池。電池壽命過短會導致在工作期間因電池漏液而導致該流量計的損壞。此流量計的設計待機壽命約為2年，但建議客戶每一年更換一次電池。建議客戶每一年檢查一次電池電極，如有銹蝕時應及時清除。長時間沒有使用流量計時，應將電池取出。
Two, the technical beters
Medium oil, urea, kerosene, petrol, chemical, water
Import and export 1"
The measurement accuracy of ± 1%
Repetitive ± 0.5%
The maximum working pressure of 20BAR
Working voltage 2.3-3.3V
The standby time of 2 years
Flow range 10-120L/MIN
Single count 0.00-9999.9
Total number of 0.00-999999.9
Units of measurement or /L, gallons of /GAL /PTS /QTS, pint, quart
A single measurement of b RESET
Three, setting
1, unit of measurement
In the standby state or the filling quantity display state, at the same time, press the MENU+RESET key for 5 seconds. Enter the unit conversion settings, press the RESET key, followed by the LTR → GAL → PT → QT → LTR select the unit of measurement, while the cumulative dosing metering unit conversion in accordance with currentdisplay. Then press the MENU key for 3 seconds, exit unit conversionsettings.
2, the cumulative dosing can be reset.
Long press RESET button, LCD full screen display, waiting for a full screen display after the end, release the RESET key, then reset the cumulative dosing filling capacity and current zero.
3, the error coefficient and total query
The standby mode, press the MENU+RESET key at the same time,LCD on the digital display error coefficient, the lower display totalflow.
Four, the calibration error coefficient
In the standby state or the filling quantity display state, press the MENU button 3 seconds, enter the calibration status. At the same time, the first digital display, press the MENU button, a digital shift,(flashing digital displacement), press the RESET button, to modify the current flashing in value, are from 0 to 9, and then to the 0. Thiscoefficient increases when the oil quantity is less, the coefficient is smaller oil quantity. Press the MENU button 3 seconds over the calibration. Return to display the current state and the current amount of filling, filling quantity display b. The calibration, such as newmetering pulse b use error coefficient of new calibration. Range calibration error coefficient: 0.1000 - 9.9999. Patients with primaryfactor is 1, the display shows oil 100 liters, the actual oil is 100 liters,if want to plus 2 liters of oil less, press the MENU button 3 seconds,according to the calibration of the 1.020. After the 98 litre. Want 96up to 1.040. Otherwise less significant for oil.
Five, maintenance and maintenance
When the battery voltage is too low, the LCD display screen appears on the battery symbol, to remind the user to replace the battery.Battery life is too short will result in the work period from battery leakage resulting in damage to the meter. The meter design standbylife span of about 2 years, but advises customers each year to replace a battery. Recommends that customers every year check a battery electrode, such as rust should be cleaned timely. Long time no use of flow time, should remove the battery.
