產品詳情
廈門晶鼎自動化科技有限公司現貨供應CS10-R電流開關，歡迎前來咨詢，謝謝！聯系人：黃明航 ，電話：05925586900/13599928764 傳真：0592-5328257 QQ:70666131
1. 應用
CL10-W作為傳統電纜室照明燈的替代方案，采用
LED作為發光光源，并采取特殊的結構，實現低成本、
高可靠、易用性的應用設計。
1. Application
The CL10-W is the substitute of the traditional cable
cabinet lamp, adopt LED as light source, and adopt
special structure, carry out low cost and high reliability
and use easily .
□ The power supply adapt to AC/DC110V~230V, The
electric circuit adopt to import IC, and the convert
efficiency is high, the heat is small, the life is long.
□ Adopt the Phoenix spring connector.
□ The control unit install in instrument cabinet, easy to
make maintenance.
□ The luminescent head is fixed in place needed light
of cable cabinet with screw conveniently and fast.
□ Little volume's luminescent head make the cable
cabinet clean and neat.
□ Choose the LED that suitable with the cable cabi-
net
illuminance, ensure illuminance effect with lower
power consumption
□ Since LED life is long, replacing is not be acted as
normal situation.
□ Connecting cable bed with illuminance head
adopts a quickly b part, easy to install and re-
place.
□ With reliable protective structure, the luminescent
head ’s mar is reduced.
□ The house adopt flame retardant material.
□ 適應電源范圍寬，AC/DC110V~230V，控制電路
采用進口IC，轉換效率高，發熱量小，壽命長。
□ 接線端子采用Phoenix彈簧接線端子。
□ LED光源控制單元安裝于開關柜儀表室，便于更
換。
□ 發光頭可用螺栓夾緊的方式安裝在電纜室需要光
照的地方，方便快捷。
□ 體積小巧的發光端可使電纜室布局整潔美觀。
□ 選用電纜室照明場合適用的LED，既降低了功耗
又保證了照明效果。
□ 在高壓柜的使用壽命期內，基于LED光源的長壽
特性，正常使用情況下不用更換LED，免除了電
纜室更換光源的風險。
□ 連接電纜與發光頭連接采用快速連接器，便
于安裝更換。
□ 發光頭采用可靠的防護結構，可有效減少不當安
裝及使用可能對LED造成的損傷。
□ 外殼采用阻燃材料。
3. 型號說明
CL10-W
10是設計序列號；
W是光源顏色白色“white”的簡寫。
4. 技術參數
□ 電源：AC/DC110V~230V
□ 功耗：<4W
□ 連接電纜：阻燃電纜2×0.5mm2
，3.5米
（電纜長度可依用戶需求提供）
□ LED：采用高亮LED，壽命不少于50000小時
□ 耐壓強度：AC2500V，1Min
□ 工作環境溫度：-25ºC~50ºC
□ 相對溫度：25%~95%（40℃）
□ 發亮?xí)r間：1800s±15% （也可按客戶要求設定）
□ 再次啟動間隔時間：不超過8秒鐘
提示：延遲時間到后，須斷開電源！等待不超過8秒，再
次送電時，燈就能重新亮起，并重算延遲時間。
4. Technique beters
□ Rated power voltage: AC/DC110V~230V
□ Power Consumption: <4W
□ Connecting cable: Flame retardant cable, 3.5m
(length is variable for demand of customer)
□ LED: Use highlight LED, the life span is no less
than for 50000 hours
□ Insulating strength:AC2500V,1Min
□ Ambient temperature:：-25ºC~50ºC
□ Relative humidity:25%~95%（40℃）
□ Lighting continuance: 1800s±15% (variable for
demand of customer)
□ Re-start interval: Less than 8 seconds.
Prompt:After delay time arrived, must disconnect power
supply! Waiting for no less than 8seconds, connect
Power supply again, the light would re-start, and
calculate a delay time over again.
CL10-W
The “10” is Design serial number;
The “W” is a brief of “White” , it is color of light
source.
3. Models explanation
2. 特點及優點 2. Features and advantages
5. 使用方法
將光源控制單元安裝于便于安全操作區域，發光
頭安裝于需要照明區域的合適位置。接通電源，光源
控制單元通過連接電纜點亮發光頭，照亮選定區域。
接通電源后，因發光持續時間的出廠標準設定為30分
鐘，30分鐘后自動熄滅。若要重新啟動，必須在斷開
電源不少于8秒后再接通電源。
建議:在每次使用后斷開電源。
5. Use b
The light source control unit mount in the easy to safety
operation region, illuminance head mounts in the suita-
ble place that the end illuminates a region in the de-
mand. Connect a power supply, illuminance head take
power from the light source control unit, illuminating a
region selected. After connecting a power supply, the
plant standard keeping on time setting that gives out
light is for 30 minutes, and automatically goes out after
30 minutes. If want a restart, have to connect again a
power supply after disconnecting power supply no less
than 8 seconds.
Suggest: to disconnect power supply after every time
use .
6. 安裝
電纜室照明燈由光源控制單元、連接電纜和發光
頭組成。光源控制單元配有接線端子可直接連接電
源，其 中 A1（+）接 AC“L”或 DC“+”，A2(-) 接 AC
“N”或DC“-”，+接連接電纜紅線，-接連接電纜黑
線。光源控制單元安裝在DIN 35mm標準導軌上，發光
頭可用螺栓夾緊的方式安裝在電纜室需要光照的地
方。
6. Installation
Cable cabinet lamp consist of light source control unit
and connecting cable and illuminance head.The light
source control unit has the wiring terminal that can
connect a power supply directly, among them, the A1
(+)connect the AC"L" or DC"+", the A2(-) connects the
AC"N" or DC"-",the + connect the red line of connecting
cable, the - connect the black line of connecting cable.
The control unit can mount at a standard DIN 35 mms
rail.The illuminance head can fix tightly in the suitable
place that the head illuminates a region in the demand
with screw .
外形尺寸圖
Dimension diagram
光源控制單元外形尺寸
Light source control unit dimension
發光頭外形尺寸
Illuminance head dimension
連接導線要求
Terminal Cross Section
10mm
導線截面積/Nominal Cross Section:2.5mm2
最大導線截面積/Max.Cross Section:4mm2
34.35
安裝示意圖
Mounting sketch map
1. 應用
CL10-W作為傳統電纜室照明燈的替代方案，采用
LED作為發光光源，并采取特殊的結構，實現低成本、
高可靠、易用性的應用設計。
1. Application
The CL10-W is the substitute of the traditional cable
cabinet lamp, adopt LED as light source, and adopt
special structure, carry out low cost and high reliability
and use easily .
□ The power supply adapt to AC/DC110V~230V, The
electric circuit adopt to import IC, and the convert
efficiency is high, the heat is small, the life is long.
□ Adopt the Phoenix spring connector.
□ The control unit install in instrument cabinet, easy to
make maintenance.
□ The luminescent head is fixed in place needed light
of cable cabinet with screw conveniently and fast.
□ Little volume's luminescent head make the cable
cabinet clean and neat.
□ Choose the LED that suitable with the cable cabi-
net
illuminance, ensure illuminance effect with lower
power consumption
□ Since LED life is long, replacing is not be acted as
normal situation.
□ Connecting cable bed with illuminance head
adopts a quickly b part, easy to install and re-
place.
□ With reliable protective structure, the luminescent
head ’s mar is reduced.
□ The house adopt flame retardant material.
□ 適應電源范圍寬，AC/DC110V~230V，控制電路
采用進口IC，轉換效率高，發熱量小，壽命長。
□ 接線端子采用Phoenix彈簧接線端子。
□ LED光源控制單元安裝于開關柜儀表室，便于更
換。
□ 發光頭可用螺栓夾緊的方式安裝在電纜室需要光
照的地方，方便快捷。
□ 體積小巧的發光端可使電纜室布局整潔美觀。
□ 選用電纜室照明場合適用的LED，既降低了功耗
又保證了照明效果。
□ 在高壓柜的使用壽命期內，基于LED光源的長壽
特性，正常使用情況下不用更換LED，免除了電
纜室更換光源的風險。
□ 連接電纜與發光頭連接采用快速連接器，便
于安裝更換。
□ 發光頭采用可靠的防護結構，可有效減少不當安
裝及使用可能對LED造成的損傷。
□ 外殼采用阻燃材料。
3. 型號說明
CL10-W
10是設計序列號；
W是光源顏色白色“white”的簡寫。
4. 技術參數
□ 電源：AC/DC110V~230V
□ 功耗：<4W
□ 連接電纜：阻燃電纜2×0.5mm2
，3.5米
（電纜長度可依用戶需求提供）
□ LED：采用高亮LED，壽命不少于50000小時
□ 耐壓強度：AC2500V，1Min
□ 工作環境溫度：-25ºC~50ºC
□ 相對溫度：25%~95%（40℃）
□ 發亮?xí)r間：1800s±15% （也可按客戶要求設定）
□ 再次啟動間隔時間：不超過8秒鐘
提示：延遲時間到后，須斷開電源！等待不超過8秒，再
次送電時，燈就能重新亮起，并重算延遲時間。
4. Technique beters
□ Rated power voltage: AC/DC110V~230V
□ Power Consumption: <4W
□ Connecting cable: Flame retardant cable, 3.5m
(length is variable for demand of customer)
□ LED: Use highlight LED, the life span is no less
than for 50000 hours
□ Insulating strength:AC2500V,1Min
□ Ambient temperature:：-25ºC~50ºC
□ Relative humidity:25%~95%（40℃）
□ Lighting continuance: 1800s±15% (variable for
demand of customer)
□ Re-start interval: Less than 8 seconds.
Prompt:After delay time arrived, must disconnect power
supply! Waiting for no less than 8seconds, connect
Power supply again, the light would re-start, and
calculate a delay time over again.
CL10-W
The “10” is Design serial number;
The “W” is a brief of “White” , it is color of light
source.
3. Models explanation
2. 特點及優點 2. Features and advantages
5. 使用方法
將光源控制單元安裝于便于安全操作區域，發光
頭安裝于需要照明區域的合適位置。接通電源，光源
控制單元通過連接電纜點亮發光頭，照亮選定區域。
接通電源后，因發光持續時間的出廠標準設定為30分
鐘，30分鐘后自動熄滅。若要重新啟動，必須在斷開
電源不少于8秒后再接通電源。
建議:在每次使用后斷開電源。
5. Use b
The light source control unit mount in the easy to safety
operation region, illuminance head mounts in the suita-
ble place that the end illuminates a region in the de-
mand. Connect a power supply, illuminance head take
power from the light source control unit, illuminating a
region selected. After connecting a power supply, the
plant standard keeping on time setting that gives out
light is for 30 minutes, and automatically goes out after
30 minutes. If want a restart, have to connect again a
power supply after disconnecting power supply no less
than 8 seconds.
Suggest: to disconnect power supply after every time
use .
6. 安裝
電纜室照明燈由光源控制單元、連接電纜和發光
頭組成。光源控制單元配有接線端子可直接連接電
源，其 中 A1（+）接 AC“L”或 DC“+”，A2(-) 接 AC
“N”或DC“-”，+接連接電纜紅線，-接連接電纜黑
線。光源控制單元安裝在DIN 35mm標準導軌上，發光
頭可用螺栓夾緊的方式安裝在電纜室需要光照的地
方。
6. Installation
Cable cabinet lamp consist of light source control unit
and connecting cable and illuminance head.The light
source control unit has the wiring terminal that can
connect a power supply directly, among them, the A1
(+)connect the AC"L" or DC"+", the A2(-) connects the
AC"N" or DC"-",the + connect the red line of connecting
cable, the - connect the black line of connecting cable.
The control unit can mount at a standard DIN 35 mms
rail.The illuminance head can fix tightly in the suitable
place that the head illuminates a region in the demand
with screw .
外形尺寸圖
Dimension diagram
光源控制單元外形尺寸
Light source control unit dimension
發光頭外形尺寸
Illuminance head dimension
連接導線要求
Terminal Cross Section
10mm
導線截面積/Nominal Cross Section:2.5mm2
最大導線截面積/Max.Cross Section:4mm2
34.35
安裝示意圖
Mounting sketch map
