產品詳情
電鍍污水處理壓濾機泵@陽江電鍍污水處理壓濾機泵80ZJW-II
1、臥螺式離心機的利益：a、運用面積小，一般只需求4—8個平米，設備簡略便當；b、密封性好，作業環境好，持續作業才調強，處理才調大；c、產品價格實惠，運用本錢相對較底，修補保養費用極低，修補簡略；d、脫泥量大，不需求清水沖刷，不會構成二次污染。
一、產品概述
ZJW型壓濾機專用泵本由公司結合各壓濾機生產廠家及使用現場的實際工況，精心設計開發的新一代無泄漏壓濾機專用泵，該產品廣泛應用于壓濾機入料泵應用尤為廣泛，通過在冶金、礦山、電廠、化工等行業中的使用，發現該系列產品具有結構合理，運行可靠，壽命長等特點。該系列產品采用獨特的水力設計及雙級葉輪的結構，確保了其性能曲線比一般YLB、UHB、HFTK等普通離心泵改造而成的壓濾機入料泵更陡，更適合壓濾機入料的特殊使用工況。jdhuiquan6.17
二、創新技術特點
1. Unique sealing device using negative pressure technology plus combined sealing device, in the increasing pressure and flow is gradually reduced, sealing components do not bear pressure, especially in the late press period due to the pump under large pressure, its innovative seal structure design, to ensure that the shaft seal basically achieved no leakage.
2. Structural design of two-stage impeller
The pump adopts the double main pump body, the structure design of the double main impeller, compleby solves the requirement that the single pump leaf wheel pump has too much vibration and noise, flat perbance curve, narrow leaf rotation path, poor perbance and so on, and the change of resistance when the filter press feed is very suitable for the requirements of high flow and low pressure feeding and small flow rate.
3. Double impeller pump than single leaf wheel pump anti-wear resistance is better
Because the double impeller pump at the lower impeller outlet line speed to obtain higher pump outlet pressure to overcome the single-leaf wheel pump in order to increase the pressure and increase the impeller line speed, resulting in impeller, pump shell wear increased shortcomings, effectively improve the life of water pump and other overcurrent components.
4. Wide range of applications
The product can be made of cast steel, high chromium cast iron (corrosion-resistant wear-resistant materials), stainless steel and other materials, can be adapted to different media needs, the user selection of a wider range.
5. Adjustable gap between impeller and pump wall
Unique bearing box design, users in the regular time after use, due to wear caused by pressure drop, can be adjusted impeller and pump wall gap to continue to ensure the high pressure of the pump, improve the service life of the pump, extend the overhaul cycle, overcome the traditional single-leaf wheel pressure filter pump due to the wear pressure drop fast, often replace the impeller service life is short
電鍍污水處理壓濾機泵@陽江電鍍污水處理壓濾機泵80ZJW-II
在出產進程中，污泥壓濾機具有不同的工藝要求，如脫水，澄清，濃縮，分級和分別。 脫水和澄清，其基本上分別懸浮液中的固體和液體，脫水是除去固相中的液相，澄清是除去液相中的固相。 濃度是溶液中液體固相的固相增加。 減速是懸浮液中不同顆粒的顆粒的開釋，并且依據顆粒標準d，被分紅大于d +且小于d。 兩組粒子組件。 分別一般是指分別200個小相溶液相。 假定液 - 液兩相是連續相，則分別僅與它們的密度差異有關; 假定一相是連續的而另一相是松懈的，則另一相松懈在連續相中以構成乳液。在這種情況下，液體的兩相被分別，并且6 IX與兩相中的密度2相關，并且還與松懈相的液滴直徑有關。 首要，脫水進程中觸及的物理參數，分別要求和模型選擇脫水進程是將固相與懸浮液中的液相分別，液相需求更好。
三、性能參數表
